By Kevin, ZIVFY · 18 years in print

Most people assume that whether a metal logo label stays on comes down to the adhesive. In practice, it comes down to the surface.

Our metal logo labels are real nickel and very thin: 0.08–0.2 mm (about 0.003–0.008 in) including the adhesive, with 0.08–0.1 mm (about 0.003–0.004 in) as our default. The thinner the label, the better it sticks. Once applied, only the logo stays on the product, with no backing film around it. On a flat, smooth, clean surface, our regular 3M adhesive holds well. On a tight curve or a coarse, deeply textured surface, no adhesive can guarantee a good hold. So this guide starts with the products and packaging where they hold best, then covers which adhesive to choose and how large or small a logo can be, and ends with how to apply them yourself.

This guide is about real metal. If you have in mind a regular sticker printed in gold or silver, or a dome sticker with a layer of clear resin on top, that is a different product. Here is how they compare: metal stickers vs dome stickers.

A silver metal logo label on a cream-colored box lid.

Which products and packaging can metal logo labels go on?

Most of them. We have made labels for every product below. What they have in common is that the label goes on an area that is flat or only slightly curved:

  • Perfume bottles and cosmetics: metal stickers for perfume bottles usually go on the flat face of the glass or the top of the cap. Compacts and cosmetic boxes work well too.
  • Gift boxes, jewelry boxes and wine boxes: the center of the lid on rigid paper boxes and wooden boxes.
  • Laptops and electronics: metal stickers for laptop lids, speakers, power banks and device panels.
  • Stationery and gifts: hard covers of notebooks and planners, and acrylic display pieces.
Gold-coloured metal logo lettering on a glass bottle.
A gold metal logo label with a globe and satellite design.
A mirror-finish metal logo label on a yellow lid.

A flat, smooth housing gives the firmest hold and shows off the metal finish best. Electronics brands selling into the EU often ask whether the materials comply with RoHS, the EU directive that restricts hazardous substances in electrical and electronic products. We can provide the RoHS report for our nickel labels and the environmental documentation for the adhesive.

Which surfaces should you avoid?

  • Tight curves. A slight curve is fine, for example a logo 3–5 cm (about 1.2–2 in) long on a scented candle jar. Once the curve gets tighter or the logo gets longer, we don’t recommend it. For more detail, see metal logo stickers on curved surfaces.
  • Coarse, deep textures. A fine texture works with the stronger adhesive. If the grooves are wide and deep, the metal only rests on the raised points and can’t sit flat.
  • Anything that is washed often or goes in a dishwasher. We haven’t tested this, so we can’t promise the labels will hold.
  • Very light items. The transfer film carries a little adhesive of its own. On a thin sheet of paper or a very light item, peeling off the film can lift the item along with it. Hold the item down with your hand while you peel.

Regular or stronger adhesive?

For most jobs, the regular adhesive is all you need. That covers every flat, smooth surface listed above.

Switch to the stronger adhesive in two cases: when the label goes on a curved surface, and when the surface has a fine texture, such as frosted plastic or a textured paper box. If you’re not sure which one you need, send us a close-up photo of the product surface and we’ll check it for you.

How large and how small can metal logo labels be?

The largest we make is about A4 size (210 × 297 mm, about 8.3 × 11.7 in). Almost every logo on a product or package is far smaller than that, so size is rarely an issue.

For small logos, keep these points in mind:

  • Any separate block or stroke smaller than 4 × 4 mm (about 0.16 × 0.16 in) gets a thin metal bridge line by default, which joins it to the parts next to it. Without one, a very small separate piece can shift or get left behind when you apply the label. If you would rather not have the bridge line, we can leave it out, but we’ll explain the possible problems first and let you decide.
  • Avoid long, thin lines and long, sharp points where you can. Over time, these are the spots most likely to lift.
  • Handle sharp corners with care. The metal is very thin, and a sharp corner can prick your finger.
  • Very small, fine parts won’t stand up to deliberate picking. In everyday use, a metal logo label holds up well, but it is still applied to the surface rather than built into the product. If you have specific requirements for how firmly it needs to hold, tell us. Some of them we can meet, and we’ll tell you plainly whether we recommend it. The decision is yours.

A compact logo version may work better than shrinking the full mark. João Queirós’s guide to testing logo readability explains how to check versions at actual size and document when each should be used.

A silver crest-shaped metal logo label on its release liner.

How do you apply metal logo labels yourself?

It works much like applying a regular sticker, except there is a clear transfer film on top.

  1. Cut them out. By default we ship full sheets: one backing sheet, about A4 size, with anywhere from a few to a few dozen logos on it. You cut them apart with scissors. If you need them pre-cut into single pieces, let us know when you order.
  2. Clean the surface. Wipe the spot with alcohol and let it dry. Oil, dust and fingerprints are the most common reasons a label doesn’t stick. The adhesive has to touch the surface directly, and even a thin layer of dust or oil in between keeps it from bonding.
  3. Peel off the backing paper. The release liner comes off easily, and the metal logo stays on the transfer film.
  4. Position the logo and press hard. Rub over the film several times with your thumb. The more pressure you apply, the better it bonds.
  5. Peel off the transfer film. The metal logo stays on the product, and you’re done.
We ship full sheets by default. You cut the logos apart with scissors.
Peel the film slowly. The metal logo stays on the product.

One thing happens fairly often: the metal logo comes up with the film as you peel. Don’t worry, and don’t try to pick it off with your fingers. Press the film back down, rub it a few more times with your thumb so the logo bonds to the surface, then peel the film again slowly.

Do metal logo labels change color?

We only make high-quality nickel labels, and nickel is the hardest of the metals used for metal labels. You can see the available colors on our metal stickers page.

If your product will be sold in a humid climate, or you have strict durability requirements, we can color the nickel labels with PVD or color-matched spray paint instead. The color will look slightly different from our standard electrophoretic coloring, in which an electric current deposits a very thin colored coating onto the nickel (all of our standard colors are made this way). In return, the labels resist oxidation better, hold up better and can meet requirements such as a 96-hour salt spray test.

To order custom metal logo labels, send us three things: your logo as a vector file (AI or CDR), the size you want, and a photo of the product or packaging the label will go on. We’ll check the file for parts that are too small or too thin, look at which adhesive suits the surface, and then send you a quote. The minimum order is 10 pieces, so for a first order you can start with 10 and test them on your own products.