By Kevin, ZIVFY · 18 years in print

Hard samples such as stone, glass and panels rarely come off the saw with clean edges. They chip, they have burrs, and the cut face is a different color from the front. In an ordinary slotted sample book, all four cut edges sit in plain view around the slot, so the first thing a buyer sees is the edge, not the material.

Edge-hiding frame pages fix this with a printed page that presses down over the sample. The window in that page is smaller than the sample, so all four edges sit underneath it and only the clean face shows. You do this step yourself: the book arrives empty, and your samples never have to be shipped to China.

The printed frame covers all four cut edges, so only the face of each sample shows.

Quick summary

  • The cut edges sit under the printed page, so your samples don't need to be cut precisely.
  • We apply the adhesive in advance, and you fit the samples in three steps.
  • Frame pages only suit hard samples. Once pressed, a page is fixed, so ranges that change often need a different format.

Covering the cut edges used to mean shipping your samples to the factory

An ordinary slotted page is simple to make and you can fit the samples yourself, but the cut edges and the gap around each slot stay visible. The older way to seal all four edges under paper is to place each sample between two sheets while the page is being bonded at the factory. Once the page is bonded, nothing more can go in, so every sample has to be cut, packed and shipped internationally first. With many styles and a large run, that freight and handling add up, and the books can't start until the samples are finished.

After years of making sample books, we had heard the same problem from buyers again and again: to cover the cut edges, you have to send us the samples. Edge-hiding frame pages are the structure our engineers worked out to solve it.

They move the sealing step from our factory to your side. Here is how the three options compare:

OptionCut edgesWho fits the samples
Ordinary slotted pageVisibleYou do
Factory-sealed pageCoveredThe factory, during page bonding, so samples must be shipped to us
Edge-hiding frame pageCoveredYou do

A frame page has three parts

The base page is slotted to your sample, and the sample sits in the slot. A strip of double-sided tape is already applied around the slot, with its release liner still on. On top is a printed page with a window cut into it. Each side of the window is at least 2 mm (about 5/64 in) smaller than the sample. The window can have rounded corners or be cut to a custom shape.

The printed page and the base page are one spread, bound together, so the printed page lifts like a flap. A number is printed beside each window, along with your style codes and brand details.

We need accurate numbers, not neatly cut samples

That 2 mm is there to absorb error. Before we start, we ask for your sample size and its plus/minus tolerance, and we cut the slot to the largest size. An oversized sample still fits. An undersized one leaves a small gap in the slot, and the window still holds it down.

A sample placed slightly crooked is fine for the same reason: the window overlaps every edge, so the part that is off still sits under the printed page and doesn't show from the front.

Thickness has some room too. We cut the slot slightly deeper than the sample, so the printed page presses down flat instead of bulging over it.

Three steps when the books arrive

  1. Lift the printed page and place each sample in its numbered slot.
  2. Peel the release liner from around the slots. Peel it all at once; there is no order to follow.
  3. Lower the printed page and press firmly around each window.
Step 1: Place each sample in its slot.
Step 2: with the samples in place, peel the liner, then press the printed page down.
Step 3: Press firmly around each window to cover the sample edges.

The only thing that can go wrong is putting a style in the wrong position. Until the liner is peeled, the printed page is loose and you can open and close it freely. So lay out a whole page of samples, check them against the numbers, and then peel.

If you press the page down and then find a sample in the wrong place, it can still be fixed. Warm the adhesive with a hair dryer, lift the printed page slowly, swap the sample and press it back. Treat this as a rescue, not as a way to change samples regularly.

Heavier samples get an extra piece of tape in the slot

Light samples are held by the ring of adhesive under the printed page alone. For a heavier sample, stick a piece of double-sided tape to the bottom of the slot first, set the sample on it, and then press the printed page down. The book can then be held upright and carried around without anything working loose, because the printed page holds every sample on all four sides.

We have made frame pages for panels, stone and glass. The thickest so far was 8 mm (about 5/16 in) glass. Cut glass edges are sharp; under the frame they are covered by paper, so they don't cut fingers when the pages are turned. For heavier or thicker samples, our heavy sample book guide explains which structure to choose.

The samples were still being cut while the books were being made

A client in the glass business needed 500 books, each holding more than 20 panel and glass samples. When he placed the order, his samples were not all cut yet. With the older method, he would have had to wait until every sample was ready and then ship more than ten thousand hard, heavy pieces to us. He didn't want the freight cost or the trouble.

He chose frame pages instead. He gave us the sizes, tolerances and thicknesses, we started on the books, and his team carried on cutting. When the books arrived they fitted the samples themselves, and he was happy with the result.

Soft samples and ranges that change often are better in another format

Soft samples don't lie flat under a frame. Buyers also like to take soft materials out and feel them, which a pressed frame prevents. Fabric belongs in a fabric swatch book. Hard samples are the opposite: running a finger across the surface tells you what you need to know, so they don't have to come out. Thin hard samples work too.

Once pressed, the page is fixed. For a range that changes every year, use a sample binder and replace pages instead of whole books; our guide on how to update a sample book covers the details.

Frame pages cost more than ordinary slotted pages, because of the pre-applied adhesive and the extra steps. The minimum order is the same as for our other sample books, so you can start with small batch sample books. Lead time is about the same.

What to send us for a quote

Send the length, width and thickness of your samples, the plus/minus tolerance, the number of samples per book and the number of books. Tell us if any styles are especially heavy. Your samples don't have to be finished; once the numbers are settled we can start, as we did for the glass client above. Request a quote on our custom sample book page and we reply within 12 hours.